甘肃回转风机厂家的回转风机被广泛应用，但是回转风机生锈该怎么处理和使用过程中怎样保证气缸内的气体不回流呢，今天由小编给大家介绍一下吧。

Gansu rotary fan manufacturer's rotary fan is widely used, but how to deal with the rust of the rotary fan and how to ensure that the gas in the cylinder does not return in the process of use? Today, let's introduce it by the editor.

回转风机生锈的处理方式，回转风机是一种靠容积变化而工作的鼓风机产品，由于风机在运行时，两个叶轮始终都是不接触的。这也就是说，不会产生磨损，由于两个叶轮之间的间隙非常小，所以不能有异物在里面，这样会导致风机停止运转。

Rotary fan rust treatment, rotary fan is a rely on volume change and work of the blower products, because the fan in operation, the two impellers are always not in contact. That is to say, there will be no wear, because the gap between the two impellers is very small, so there should be no foreign matter in it, which will cause the fan to stop running.

但是甘肃回转风机厂家主要用于污水处理，养殖等场合，由于维护不到位，往往会使风机内部生锈，这样就减小了两叶轮之间的间隙，出现卡死现象，使风机停止运转，这是就需要对回转风机的内部叶轮进行除锈处理。

However, Gansu rotary fan manufacturers are mainly used for sewage treatment, breeding and other occasions. Due to the inadequate maintenance, the internal rust of the fan is often caused, which reduces the gap between the two impellers and causes the fan to stop running. This requires derusting the internal impeller of the rotary fan.

好的方法就是拆开用砂纸打磨，然后再进行安装即可。由于风机在安装时对间隙要求比较严格，一般是是0.05至0.1毫米之间，所以没有专业人员指导的情况下，不要自己拆装。

A good way is to take it apart, grind it with sandpaper, and then install it. Due to the fan in the installation of the clearance requirements are relatively strict, generally between 0.05 to 0.1 mm, so there is no professional guidance, do not disassemble.

回转式鼓风机靠汽缸内偏置的转子偏心运转，并使转子槽中的叶片之间的容积变化将空气吸入、压缩、吐出。在运转中利用鼓风机的压力差自动将润滑送到滴油嘴，滴入汽缸内以减少摩擦及噪声，同时可保持汽缸内气体不回流。回转风机在设备通气前的检测时运行注意事项正式通水前，先进行回转风机通气检测，通气前先启动风机，开启风机风量的百分之五十，送至生化池曝气管道中检测，检查管道所有节点焊接安装质量，不能有漏气现象发生，不易检测时应用肥皂水进行检测。此时，风机运转特别注意，比如风机不能空载运行，风机润滑油在没有压力时，润滑油不能自动循环使用，风机有缺油运行的风险，因此在试漏检测时，要不断的从进风口加适量润滑油让风机正常运转。

The rotary blower relies on the eccentric operation of the offset rotor in the cylinder, and makes the volume change between the blades in the rotor slot to suck in, compress and eject the air. During the operation, the pressure difference of the blower is used to automatically send the lubrication to the oil dripping nozzle and drop it into the cylinder to reduce the friction and noise, while keeping the gas in the cylinder from returning. Before ventilation, start the fan, turn on 50% of the air volume of the fan, and send it to the aeration pipe of the biochemical tank for detection. Check the welding and installation quality of all nodes of the pipe, and no air leakage is allowed. When it is difficult to detect, use soapy water for detection. At this time, special attention should be paid to the operation of the fan. For example, the fan can't run without load, the lubricating oil can't be recycled automatically when there is no pressure, and the fan has the risk of oil shortage operation. Therefore, during the leakage test, it is necessary to continuously add an appropriate amount of lubricating oil from the air inlet to make the fan operate normally.

本文由甘肃回转风机厂家整理提供，感谢您的阅读，希望以上内容对您有所帮助，如您想了解更多精彩内容请点击我们的官网：http://www.sdyqtc.com。

This article is provided by Gansu rotary fan manufacturer. Thank you for your reading. I hope the above contents can help you. If you want to know more wonderful contents, please click our official website: http://www.sdyqtc.com .

相关文章： 陕西离心式风机厂家 净化器 气力输送设备厂家 油烟 甘肃回转风机厂家